Drivers Abstract Washington
Drivers Aastra Phone
Drivers Aastra Wireless
Drivers Abstract Ohio

You must transfer to the hard disk the firmware through ftp program MDDT (SAM). After loading the firmware you have to block the card with the command BLDBI, transfer the firmware with the command CNBLI, on positive result, run the commands CNBSI CNBCI. Ready to talk to sales? Find a Partner (844) 319-5912 Email Us. MiCloud Technical Support; Mitel Technical Support. Declaration of Conformity Aastra 6735i and 6737i aastra6735i 6737i ce 2011-11 (1).pdf. RN-001037-03 REV37 6735i 6737i Release Notes 3.3.1 SP4 HF9 (2).pdf 58014472 REV03 6800 Series SIP Phone Release Notes 4.2.0 SP2 (2).pdf 58014472 REV02 6800.

On the web interface of your Aastra phone you will need to enter the IP address of your TFTP server (your PC) and you will have to enter the file name of the firmware file that you placed in the root directory of the TFTP server. Click Download Firmware. Once the firmware has installed the Aastra phone should boot normally. When prompted, enter your username and password. The Default setting for Aastra phones is Username: Admin, Password: 22222. 6) This will display your Telephones web interface. 7) Select the FIRMWARE UPDATE link on the bottom left side of the screen. 8) This will display the Firmware.

Introduction

Aastra IP phones 6753i, 6755i, 6757i, 6757i-CT, and 6731i have been tested with MAXCS and certified by AltiGen as third-party IP phones for MAXCS Release 6.5 and above. This document shows how to configure these models of Aastra IP phones, how to deploy the phones in volume, and the MAXCS features that are not supported by the Aastra IP phone.

We recommend that you quickly go through the configuration steps for a single phone and then focus on 'Deploying Aastra phones in volume', even if you just have one phone to configure.

Prerequisites

MAXCS 6.5 with Quickfix (6.5.0.1206) or above
Aastra IP phone 6753i (53i), 6755i (55i), 6757i (57i), 6757i-CT (57i-CT) or 6731i (31i)
An AltiGen third-party SIP Device license for each Aastra IP phone

Configure Extension to Accept 3rd Party SIP Phone

In MaxAdmin, select PBX > Extension Configuration > General, and create an extension with Enable IP Extension and Enable 3rd Party Sip Device checked. Extension 100 is used in this example.
Note: Do not configure Static IP address for 3rd party SIP device. This may cause SIP registration failure.
In MaxAdmin, select PBX > AltiGen IP Phone Configuration. Select extension 100 and on the General tab, in the 3rd party SIP Device panel, check Enable SIP Telephony Service. This will enable the extension to use SIP Hold, Transfer, and Conference.

Set Up the Aastra IP Phone

WARNING! The Aastra IP phone uses a 48V DC power adapter. Do NOT plug the adapter into an AltiGen IP phone. This will cause severe damage to the AltiGen IP phone.

WARNING! Some Aastra IP phone power adapters (48V DC output) can only take 110V AC as input. If you are in a country that uses 220V AC as an input, a transformer from 220V AC to 110V AC may be required. Whether the adapter can support 220V AC as an input can be found in the label of the adapter.

Find the IP Address

Attach the network cable to the Aastra phone. A DHCP server is required in the network.
Power up the Aastra phone and wait for it to fully start up.
Press or Options button on the phone.
Select Admin Menu and enter the default password 22222.
Under Network Setting > IP Address, find out the IP address of the Aastra phone. In this example, we are using IP address 10.10.1.194.

Log in to the Web Interface

Open a web browser and type http://10.10.1.194/
Enter the account, admin, and the default password, 22222.
Check firmware version from Status > System Information, Firmware Information section Aastra IP Phone Configuration Guide

Update the Firmware (if the version is not 2.5.1.x)

For 6753i, Go to http://www.aastratelecom.com/cps/rde/xchg/SID-3D8CCB6A- A1AB1A25/03/hs.xsl/21543.htm to download firmware, 6753i (53i) SIP, V2.5.1.2000 patch, July 09.
For 6755i, Go to http://www.aastratelecom.com/cps/rde/xchg/SID-3D8CCB6A- 2AFB3DC1/03/hs.xsl/21554.htm to download firmware, 6755i (55i) SIP, V2.5.1.2000 patch, July 09.
For 6757i, Go to http://www.aastratelecom.com/cps/rde/xchg/SID-3D8CCB73- 1AC50F14/03/hs.xsl/21552.htm to download firmware, 6757i (57i) SIP, V2.5.1.2000 patch, July 09.
For 6757i-CT, Go to http://www.aastratelecom.com/cps/rde/xchg/SID-3D8CCB73- 1AC50F14/03/hs.xsl/21550.htm to download firmware, 6757i CT (57i CT) SIP, V2.5.1.2000 patch, July 09
For 6731i, Go to http://www.aastratelecom.com/cps/rde/xchg/SID-3D8CCB73- 1AC50F14/03/hs.xsl/32093.htm to download firmware, 6731i SIP, V2.5.1.2000 patch, July 09

Run AltiGen TFTPNAT.exe application and unzip the file ****.st (**** is the name of Aastra phone model; for example, the file name for the 57i phone is 57i.st) to TFTPNAT.exe’s working directory. Assuming that TFTPNAT.exe is running on a server with IP address 10.10.0.228.
In the Aastra browser configuration, under Advanced Settings > Configuration Server > Setting > Download Protocol, select TFTP.
Under Advanced Settings > Firmware Update, change the Server IP to 10.10.0.228. Also, change the File Name to ****.st (**** is the name of Aastra phone model; for example, the file name for the 57i phone is 57i.st).
Note: The Path field needs to be blank before the download will work.
Click Download Firmware and follow the instructions in the browser to update the firmware.

Configure Aastra Phone Settings through Web Interface

Important Note: For every configuration page, click the Save Settings button after you change the configurations. You can finish all the changes for different configuration pages and reboot the phone once for all the changed settings to take effect.

Go to Advanced Settings > Global SIP > Advanced SIP Settings > Explicit MWI Subscription. Select Enabled.
Go to Advanced Settings > Global SIP > Advanced SIP Settings > Explicit MWI Subscription Period. Set to 60.
Go to Advanced Settings > Global SIP > Basic SIP Authentication Settings
Enter Phone Number 100.
Enter Authentication Name 100.
Enter Password of extension 100 defined in the AltiGen extension configuration screen.
Go to Advanced Settings > Global SIP > Basic SIP Network Settings
[Assuming 10.10.0.228 is the AltiGen MAXCS server IP address]
Set Proxy Server to 10.10.0.228.
Set Proxy Port to 5060.
Set Registrar Server to 10.10.0.228.
Set Registrar Port to 5060.
Set Registration Period to 60.
Go to Advanced Settings > Global SIP > RTP Settings
Set DTMF Method to SIP INFO.
Each phone can be configured up to 3 lines with 3 different extension numbers. For each extension number, a third-party SIP device license is required.
Go to Basic Settings > Preferences > General, and set Local Dial Plan to SIP dial plan:
0|911|##|#[1-3]x|#[5-9]x|#41xx|#4[2-9]|xxx+^|[1-7]xx|9[2-9]xxxxxx|91[2-9]xxxxxxxxx
- 0 means user can dial 0 to ring operator extension or WG defined in the AltiGen server
- 911 means accepting 911
- ## means accepting ## to access voice mail
- #[1-3]x means accepting feature code #1x, #2x, and #3x
- #[5-9]x means accepting feature code #5x, #6x, #7x, #8x, and #9x
- #41xx means accepting system call park with two-digit ID
- #4[2-9]xxx+^ means accepting other feature code starting #4 with extra numbers and ending with a Send or # key
- [1-7]xx means your extension length is 3-digit with prefix starts with 1 to 7. (This means extension 123 is a valid extension number, but 823 or 923 are not valid extension numbers).
  If your extension digit length is 4, then change [1-7]xx to [1-7]xxx.
- 9[2-9]xxxxxx means dialing trunk access code 9 plus 7-digit local call. If you local call is 10-digit dialing, you need to change this to 9[2-9]xxxxxxxxx
- 91[2-9]xxxxxxxxx means dialing trunk access code 9 plus 11-digit long distance number except 911.
- Note: if the

Drivers Aastra